Kt Lcd3 Ebike Display User Manual Español
Kt Lcd3 Ebike Display User Manual Español Rating: 8,6/10 990 votes
The new KT-LCD3 USB now has a 5v USB port to charge your phone, GPS or run headlights. The power source will come from your main battery so now you no longer have to bring an extra battery to power your lights or phone. The KT-LCD3 USB comes with mounting bracket, rubber shims and screws ready to install and go. It also comes with a manual and 5 pin green HIGO plug compatible with the Sondors bikes. This LCD will work with any of our 20, 25 & 35a KT controllers.
- Kt Lcd3 Display
- Kt Lcd3 User Manual
- Kt Lcd3 Ebike Display
- Kt Lcd3 Manual
- Kt-lcd3 Ebike Display User Manual
- Kt-lcd3 Ebike Display For Sale
Backlit LCD Display
On/Off Power Button
View and Download KEC KT-LCD3 user manual online. EBike Special Meter. KT-LCD3 Cyclometer pdf manual download. ELECTRIC BICYCLE METER KT—LCD3 Product User Manual In display 3, hold button (SW) shortly again to enter display 1. In each display interface, if you hold button (SW) long, the meter will be powered-off together with that of the. KT-LCD1 eBike Special Meter User Manual - Suzhou KUNTENG Electronics Co., Ltd.9- ELECTRIC BICYCLE METER KT—LCD1 Product User Manual automatically display (flicker) fault code. You can’t exit the fault code display only the fault is removed. KT-LCD3 eBike Special Meter User ManualV3.0 - Suzhou KUNTENG Electronics Co., Ltd. The KT-LCD3 USB comes with mounting bracket, rubber shims and screws ready to install and go. It also comes with a manual and 5 pin green HIGO plug compatible with the Sondors bikes. This LCD will work with any of our 20, 25 & 35a KT controllers. Backlit LCD Display. On/Off Power Button. Battery Capacity Indicator Display. Odometer Display. KT-LCD3 e-Bike Display User Manual V3.0 Dear customer, please read this manual before you use KT-LCD3 instrument. The manual will guide you use the instrument correctly to achieve a variety of vehicle control and vehicle status displays.
KT-LCD3 E-Bike Computer The KT LCD3 is a powerful on-board computer that controls many key functions of your E-Bike from maximum speed, pedal assist levels, wheel size and much more. Listed below the specific functions. There are so many bikes that fall into this generation you are better off using process of elimination. If your bike has a bottle battery, it’s either Generation 1 or Generation 2. If your bike has a triangle battery AND a rectangular LCD based on the KT-LCD3, you fall into this generation. The picture on the right is a SONDORS-KT LCD3 LCD. Note: This electric bike ebike LCD Display is only compatible with KT brand controller. If you have any questions can be consulting me, I will promptly answer for you! Product Description 24V 36V 48V electric bike bicycle intelligent Control Panel LCD3 Display for ebike ( Without the waterproof port ) 1.
Battery Capacity Indicator Display
Odometer Display
Maximum Speed Display
Average Speed Display
Single and Total Trip Distance Display
Single and Total Trip Time Display
Kt Lcd3 Display
Motor Temperature Display
Motor Power Display
Kt Lcd3 User Manual
Brake Display
Backlight and Headlight Display
5 Pedal Assist Levels
Cruise Function
Battery Voltage
Integrated USB port (available only with Julet Quick Connect Anti-Water Lines)
5 pin green HIGO waterproof plug
Here are the standard LCD settings:
P1 = 100
P2 = 6
P3 = 1
Kt Lcd3 Ebike Display
P4 = 0
P5 = 12
C1 = 02
C2 = 0
Your new TAG Heuer chronograph combines the technical features of an authentic sports watch. For the TAG Heuer chronographs Carrera - Monaco - Monza – water-resistance to 50 meters. – luminescent hands and hour-markers – leather strap with folding buckle and security push buttons or steel strap with folding buckle. Tag heuer monaco ls calibre 12 user manual 2017. Their high frequency ensures excellent mechanical precision. A number of TAG Heuer automatic movements are awarded an Official Swiss Chronometer Control (C.O.S.C.) Certificate, the ultimate recognition of precision and reliability. DESCRIPTION TAG Heuer Calibre 12, Swiss Made. Automatic calibre. Diameter: 30 mm (13¼') — 59 rubies.
C3 = 8
C4 = 3
C5 = 10
C6 = 3
C7 = 1
C8 = 0
C9 = 0
C10 = n
C11 = 0
C12 = 4
Kt Lcd3 Manual
C13 = 0
C14 = 2
Video on how to get to setting mode
*disclaimer we are not responsible for any accidents, fire outbreak, explosions or any kind of damage or injury due to the use of our batteries and products. Please take all necessary precaution with the use of our products. Use at your own risk. For return and warranties please see https://electrobikeworld.com/p/return-policy
Reviews
Kt-lcd3 Ebike Display User Manual
Featured Products
Kt-lcd3 Ebike Display For Sale
The LCD screen has a handlebar mounted switch with three buttons, UP, DOWN, and a center Power button.
1. Start with battery and handlebar switch on. The LCD will be off.
2. Turn on LCD by pressing and holding POWER? button. Holding the UP button will turn on the backlight if needed.
3. Within 5 seconds of turning LCD on, press and hold BOTH UP?, and DOWN? buttons for a few seconds until the center speed indicator starts to flash.
4. The flashing field is the maximum speed the motor will spin in Kilometers per hour. 32 kph is 20 mph. Set that to any value you want using UP? and DOWN?. Press POWER ?to advance to the next setting
5. The flashing number at the bottom is the wheel size as in “26 in”. Use the UP ?and DOWN? buttons to set. (20 or 24 or 26 or 27.5 or 28 or 29 options). Press POWER? to advance to next setting.
6. The flashing units of measure show if the display is configured for metric or imperial measures. Again, use UP ?and DOWN ?if you need to change it. You may have to cycle through until you find the right combination. Press POWER? to advance to next step.
7. At this point, nothing will be flashing. But the display still shows the settings for max speed, tire size, and metric/imperial units. Press both UP ?and DOWN? to advance to setting the P values.
8. The bottom line of the display changes to a flashing “P1 46” to show the current value of the P1 parameter. Use the UP? and DOWN? buttons to change the value to 100 ?for the your ebike. When done, press POWER to advance to the next value.
9. The P2 value will flash now. Again us UP ?and DOWN ?buttons to set the value to 6?.
10. Continue on to set any other desired parameters. Brief explanations are as follows. For detailed instructions, see the LCD manual.
P1 Motor Characteristic Parameter Setting Mode (46)
P2 Wheel Speed Pulse Signal Setting Mode (0)
P3 Power Assist Control Mode (1)
P4 Handlebar Startup Mode (0)
P5 Power Monitoring Mode (12)
C1 Power Assist Sensor and Parameter Selection Mode (2)
C2 Motor Phase Classification Coding Mode (0)
C3 Power Assist Ratio Gear Initialization Mode (8)
C4 Handlebar Function Setting Mode (4)
C5 Controller Maximum Current Adjustment Mode (8)
C6 Backlight Brightness Adjustment Mode (3)
C7 Cruise Function Setting Mode (0 ). Setting to 1 enables cruise. While riding, hold the DOWN button to enable cruise control. A 'C' will appear in the pedal assist field. Using the throttle or brakes will disable the cruise.
C8 Motor Operating Temperature Display Mode (0)
C9 Power-on Password Setting Mode (0)
C10 Automatic Restore Default Setting Mode (n)
C11 Attribute Selection Mode (0)
C12 Controller Minimum Voltage Adjustment Mode (4)
C13 ABS brakes of the controller and parameters of anti-charge control (0)
C14 Power-assist tuning parameters (2)
original set is P1=46,P2=0,P3=1,P4=0,P5=12 , c1=2 c2=0 c3=8 c4=4 c5=8 c6=3 c7=0 c8=0 c9=0 c10=n c11=0 c12=4 c13=0 c14=2 , we will not take responsibility for controller failure if you change settings on lcd display .
Press and hold POWER at any time to exit the setup mode.
1. Start with battery and handlebar switch on. The LCD will be off.
2. Turn on LCD by pressing and holding POWER? button. Holding the UP button will turn on the backlight if needed.
3. Within 5 seconds of turning LCD on, press and hold BOTH UP?, and DOWN? buttons for a few seconds until the center speed indicator starts to flash.
4. The flashing field is the maximum speed the motor will spin in Kilometers per hour. 32 kph is 20 mph. Set that to any value you want using UP? and DOWN?. Press POWER ?to advance to the next setting
5. The flashing number at the bottom is the wheel size as in “26 in”. Use the UP ?and DOWN? buttons to set. (20 or 24 or 26 or 27.5 or 28 or 29 options). Press POWER? to advance to next setting.
6. The flashing units of measure show if the display is configured for metric or imperial measures. Again, use UP ?and DOWN ?if you need to change it. You may have to cycle through until you find the right combination. Press POWER? to advance to next step.
7. At this point, nothing will be flashing. But the display still shows the settings for max speed, tire size, and metric/imperial units. Press both UP ?and DOWN? to advance to setting the P values.
8. The bottom line of the display changes to a flashing “P1 46” to show the current value of the P1 parameter. Use the UP? and DOWN? buttons to change the value to 100 ?for the your ebike. When done, press POWER to advance to the next value.
9. The P2 value will flash now. Again us UP ?and DOWN ?buttons to set the value to 6?.
10. Continue on to set any other desired parameters. Brief explanations are as follows. For detailed instructions, see the LCD manual.
P1 Motor Characteristic Parameter Setting Mode (46)
P2 Wheel Speed Pulse Signal Setting Mode (0)
P3 Power Assist Control Mode (1)
P4 Handlebar Startup Mode (0)
P5 Power Monitoring Mode (12)
C1 Power Assist Sensor and Parameter Selection Mode (2)
C2 Motor Phase Classification Coding Mode (0)
C3 Power Assist Ratio Gear Initialization Mode (8)
C4 Handlebar Function Setting Mode (4)
C5 Controller Maximum Current Adjustment Mode (8)
C6 Backlight Brightness Adjustment Mode (3)
C7 Cruise Function Setting Mode (0 ). Setting to 1 enables cruise. While riding, hold the DOWN button to enable cruise control. A 'C' will appear in the pedal assist field. Using the throttle or brakes will disable the cruise.
C8 Motor Operating Temperature Display Mode (0)
C9 Power-on Password Setting Mode (0)
C10 Automatic Restore Default Setting Mode (n)
C11 Attribute Selection Mode (0)
C12 Controller Minimum Voltage Adjustment Mode (4)
C13 ABS brakes of the controller and parameters of anti-charge control (0)
C14 Power-assist tuning parameters (2)
original set is P1=46,P2=0,P3=1,P4=0,P5=12 , c1=2 c2=0 c3=8 c4=4 c5=8 c6=3 c7=0 c8=0 c9=0 c10=n c11=0 c12=4 c13=0 c14=2 , we will not take responsibility for controller failure if you change settings on lcd display .
Press and hold POWER at any time to exit the setup mode.